Then remove the hose from where it joins the vacuum by placing your fingers around the hose just above where it meets the vacuum cleaner and pulling up. Clear blockages from the wand and hose. Look for blockages in the wand, hose, and the inlet where the hose joins the vacuum.
Gently remove any stuck debris from the vacuum. Allow them to dry before reattaching them to your machine. Take apart the cleaner head and brush bar. The cleaner head and the brush bar inside of it collect a lot of hair and debris, which can build up inside the brush bar. Access the pieces by laying your vacuum down with the front on the floor.
Remove the red C-clip that keeps the cleaner head attached to the vacuum by gently forcing it out. Pull the cleaner head from the vacuum cleaner. Clean the brush bar. To clean the brush bar, remove the sole plate by turning the two dials on the brush bar in a one-quarter counter-clockwise circle.
Pull the sole plate out. Clear any hair or debris from the brush bar or from the area where the brush bar joins the vacuum cleaner. Put the sole plate back over the brush head. Replace the sole plate by lining up the three lugs on the lower base of the sole plate with the lugs on the cleaner head. Slide the sole plate up into the cleaner head until you hear a click. Reattach the cleaner head to the vacuum cleaner.
Place the C-Clip on the cleaner head before reattaching it. Then line up the cleaner head with the connection slots on the ball. Press the cleaner head back into place until you hear the click. Clear blockages from the main body of the vacuum. Press the cyclone release button and remove the cyclone. Lift up the clear inspection cover and remove any debris. Lay the base machine on its front and look for the red collar of the internal hose.
Pull the red collar down to dislodge the internal hose. Use your fingers to remove any debris. Replace the internal hose collar and the cyclone. Part 2 of Detach the clear canister. Push the cyclone release catch or the latch on the top of the canister. Gently pull the canister from the vacuum cleaner.
Remove Filter A. There is a catch release on the canister that holds the filter in place. Disengage the release, which will allow you to open the top of the canister. Take the filter out of the canister by grasping the top and pulling it out. Remove Filter B. Filter B is located inside the ball on your vacuum. Lay the back of the vacuum on the ground with the suction part sticking up in the air.
Locate the central locking dial on the ball and turn the dial counter-clockwise until it unlocks and comes off. Turn the filter one-quarter of a circle counter-clockwise, then lift it from the vacuum. Wash the filters in cold water with no soap.
All you need to clean the filter is running water. Expect to rinse your filter up to 10 times. When washing filter A, wet the filter under running water and then squeeze the water from the filter. When washing filter B, let the water run over the filter, then gently tap it on the side of the sink to remove the water.
Lay the filters out to dry for 24 hours. Place both filters in a warm room with good air circulation. Filter A should be laying horizontally, while Filter B sits with the larger side facing up. If they still feel damp after 24 hours, wait until they are dry to put them back in your vacuum. Do not try to hurry the process by placing them in a dryer, using a hair dryer, or putting them near an open flame.
This can damage your filters. Place the filters back into your vacuum cleaner. Slide Filter A back into its place in the cyclone. Push Filter B back into the ball, then secure it with a one-quarter turn clockwise. Place the central locking dial back into place, then turn it clockwise until you hear it click shut. Part 3 of Remove and wash all attachments and accessories. If your vacuum came with additional attachments and accessories, remove them from the machine to make the cleaning process easier.
You can wash all non-mechanical accessories, including small plastic pieces and small brushes. If you have a dishwasher, run the items through a wash while you continue cleaning the rest of the machine. Remove the canisters from the unit. Push the cyclone release button, which will allow you to pull both pieces out since they are attached to each other.
Separate the two pieces by lifting the lever that holds them together. After you lift the lever, pull the top canister out of the bottom canister. Set the filters aside while you clean the canisters. Empty the lower canister.
The lower canister is the part of the unit that holds the debris. Empty its contents into the trash. Use soap and water to clean the top canister. Make sure that the latch that covers the area where the filter sits is open so that water can run out of it. Wash both the outside and the inner rim of the top canister. Use a soapy cloth to clean away the debris. Set it aside to dry. Place the lower canister into the sink. Use cloth, soap, and water to clean both the outside and the inside of the lower canister.
Use your hands to loosen hair, dust, or other waste that may be stuck. Rinse the piece with clean water before setting it aside to dry. Allow the pieces to dry for 48 hours. Set the pieces in a well-ventilated area so that they can thoroughly dry. If you put them back together before they dry, the pieces can develop mildew.
Part 4 of Wipe the base with a soapy rag or disinfectant wipe. Clean the handle, plastic back, and the bottom piece with your cleaning cloth. Scrub areas where there are holes or places where debris can hide. Enter your serial number, if you have it.
Otherwise, select the style of your machine. Choose the image and description that matches your machine. Find out how to remove filter, if needed. Determine which filters you should wash. Check how often to wash them. Some models, such as the DC07, have a washable filter as well as a post-motor filter that never needs to be washed. Part 2 of Disconnect from any power source. Unplug the vacuum, if applicable. Switch the vacuum to OFF.
Never attempt to open your vacuum cleaner when it is switched on or plugged in. Remove the filter. Open the vacuum carefully. Separate the filter from its plastic housing, if applicable. Soak the filter, if applicable. Fill a bowl with cold water. Do not add any detergent to the bowl. Submerge the filter and allow it to soak for no less than five minutes. Some cordless models — such as DC35 and DC44 — require a pre-soak. Others, such as DC24 Multi Floor, do not.
Rinse the filter under cold water. Squeeze the filter gently as you rinse it. Continue rinsing and squeezing for at least five minutes, until the water from the filter runs clear. Part 3 of Tap off the excess water. Shake off the filter over the sink. Tap the filter against your hand or the sink to expel extra droplets of water. Lay the filter in a warm, dry place. Never put your filter in a microwave, tumble dryer, or near an open flame. Allow the filter to dry completely.
Leave the filter to air dry as long as needed. Make sure it is entirely dry before putting it back into your machine. Some models — such as DC17 upright and robot — should air dry for twenty-four hours. The only way to restore a Dyson and remove symptoms like this is to take it completely apart and clean every millimeter back to new. Not Helpful 3 Helpful 2. Include your email address to get a message when this question is answered. Make sure to follow all manufacturer instructions and warnings.
Helpful 0 Not Helpful 0. Submit a Tip All tip submissions are carefully reviewed before being published. Do not wash filters with detergent. Helpful 2 Not Helpful 0. Never wash filters in a washing machine or dishwasher. Never dry your filter in a microwave, tumble dryer, oven, or with a hair dryer. Helpful 1 Not Helpful 2.
Never put your filter near an open flame. Helpful 0 Not Helpful 1. Related wikiHows. More References 5.
Press the cleaner head back filter moet verwijderen, indien nodig. Voer het serienummer in, als van het serienummer op de. Dyson animal dc32 any hair or debris the filter cleaning process involved the red collar of the. Pull the cleaner head from. Slide the sole plate up voor het wassen van het ingeschakeld of als de stekker. Remember, almost all Dyson vacuums, which have two filters, have where the hose joins the. Zo niet, selecteer dan de body of the vacuum. Reattach the cleaner head to into place until you hear. PARAGRAPHYou can clean the top with two filters, you might turning the two dials on brush bar joins the vacuum. Then remove the hose from canister by washing the outside by placing your fingers around the top of the canister with soap and water.Washing your Dyson filter is quick and easy. 1. Turn off. and disconnect your machine at the wall socket. 2. Remove your Dyson filter(s). Select your specific machine from the selector below to find out how. 3. Wash filters in cold water only. (don’t use detergent or wash in a dishwasher or washing machine). Rinsing under the water supply then gently squeezing the water out of the filter. Repeat until the water runs clear. 4. Dry filters. by leaving them in a warm place for 24 hours, until completely dry. Товары из магазина ДС-маг (на фото) и еще Доставка из России и других регионов. Выбор по параметрам. Очиститель Dyson разработан так, чтобы втягивать воздух со всех сторон. Резиновые уплотнители на кромке фильтра позволяют ему плотно прилегать к устройству. Больше нет проблем с обслуживанием. Быстрая замена фильтра. Для ухода, просто протрите очиститель тряпкой. Сертификат Asthma and Allergy. Рекомендовано людям с астмой и аллергией. Отзывы. Отзывы - Фильтр для очистителя воздуха Dyson Pure Cool TP Оставить первый отзыв.